Printed circuit boards form a major part in almost all electronic gadgets and devices. Manufacturers can be provided with drawn designs by amateur electricians and use them in manufacturing of PCB, as it is not such a difficult process after all. Multi layer, single side and double side boards are the three categories of these boards. Materials made of nickel, aluminum or copper are the ones that are used in conducting them. Density and complexity of the circuits are the determinant factors when selecting the conduction material. Here are the stages that are involved in the making of the boards.
The backing is first plated using a conductive material. Into it, holes are drilled in order for the improvement of conduction in between the layers. Scrubbing of the board is performed to get rid of any unwanted small particles of the conductor. These are then recycled using such methods as filtration. In case the copper particles are not recycled, there could be serious environmental impact if it combines with the other wastes.
The board is then cleaned. Etching also takes place to allow for proper adhesion in the next stage. Once this has been carried out, there is an addition of another layer of conductor. The process of electrolysis copper plating is applied in order to conduct the holes that had been drilled previously. Both alkaline based and acidic based solutions such as copper sulfate can be used to enhance pH balance.
The circuit's final design is arrived at with the use of photo imaging. Electroplating copper also helps in arriving at the final required thickness. Application of a thin layer of tin or lead solder takes place to allow for the protection of the final circuits. Removal of the unwanted copper is done as it will not be part of the final circuit. Its etching can be carried out using an acidic or alkaline solution.
Alternative resists can also be obtained by use of other volatile organic compounds or photosensitive ones. These ones can be applied either wet or dry. When exposed to ultraviolet light, the compounds normally harden.
A roller, squeegee, spray or silk screen can be used to apply the liquid resist. The liquid can be applied on either or both sides or just on a specific area on the surface. Light can be used in order to get better circuits.
The last stage in this process is forming multi layer panels. The layer's inner cores are assembled together. The resulting product is like a book which has a copper foil with sheets of epoxy that are alternating.
The book is positioned into a laminating press and then high pressure as well as heat is applied to it. The intense heat will eventually cause the sheets to melt down and a bond will be formed. Next, there are holes that are drilled into it. Prior to this, it should undergo some trimming and buffing. Manufacturing of PCB can only be successful if all these steps and guidelines are clearly followed to the latter.
The backing is first plated using a conductive material. Into it, holes are drilled in order for the improvement of conduction in between the layers. Scrubbing of the board is performed to get rid of any unwanted small particles of the conductor. These are then recycled using such methods as filtration. In case the copper particles are not recycled, there could be serious environmental impact if it combines with the other wastes.
The board is then cleaned. Etching also takes place to allow for proper adhesion in the next stage. Once this has been carried out, there is an addition of another layer of conductor. The process of electrolysis copper plating is applied in order to conduct the holes that had been drilled previously. Both alkaline based and acidic based solutions such as copper sulfate can be used to enhance pH balance.
The circuit's final design is arrived at with the use of photo imaging. Electroplating copper also helps in arriving at the final required thickness. Application of a thin layer of tin or lead solder takes place to allow for the protection of the final circuits. Removal of the unwanted copper is done as it will not be part of the final circuit. Its etching can be carried out using an acidic or alkaline solution.
Alternative resists can also be obtained by use of other volatile organic compounds or photosensitive ones. These ones can be applied either wet or dry. When exposed to ultraviolet light, the compounds normally harden.
A roller, squeegee, spray or silk screen can be used to apply the liquid resist. The liquid can be applied on either or both sides or just on a specific area on the surface. Light can be used in order to get better circuits.
The last stage in this process is forming multi layer panels. The layer's inner cores are assembled together. The resulting product is like a book which has a copper foil with sheets of epoxy that are alternating.
The book is positioned into a laminating press and then high pressure as well as heat is applied to it. The intense heat will eventually cause the sheets to melt down and a bond will be formed. Next, there are holes that are drilled into it. Prior to this, it should undergo some trimming and buffing. Manufacturing of PCB can only be successful if all these steps and guidelines are clearly followed to the latter.
About the Author:
You can visit the website www.becman.com for more helpful information about What Goes Into Manufacturing Of PCB
No comments:
Post a Comment